Plumbing Basics: Your Key to Installing a Bathtub
Plumbing Basics: Your Key to Installing a Bathtub
Blog Article
On this page in the next paragraph you might get some brilliant guidance regarding How to Install a Bathtub Yourself.
:max_bytes(150000):strip_icc()/adhesive-type-tub-and-shower-surround-2718959-hero-22d394dc48de474a988eeaad88e9d7b0.jpg)
Installing a tub isn't specifically rocket science, however it does require solid plumbing, woodworking, as well as sometimes, tiling abilities. Changing an old tub with a new one is likewise a moderately tough project. If the old tub is easily accessible, the project can move immediately; if you have to open a wall to remove the old tub as well as position the new bath tub, the job is much harder. In either case, the project is within a house handyman's skills, although you will need a helper to leave the old tub and embeded in the new one. Make sure you have actually qualified yourself for the work as well as fit trying it. As opposed to working with a professional to take over a halfway-completed task, it is much better to consider using one prior to you begin. Opportunities are you may need an expert plumber to make tube connections.
This article will certainly aid you mount a new bathtub in your restroom if you have actually already gotten a brand-new tub and don't require to change the setup of your previous water system pipelines.
Your tools as well as material checklist need to comprise the following:
Getting ready for the Installation
To start with, the supporting framework provided with the bath ought to be fitted (if called for) according to the supplier's guidelines. Next, fit the faucets or mixer to the tub. When suitable the faucet block, it is necessary to ensure that if the faucet features a plastic washer, it is fitted in between the bathroom as well as the faucets. On a plastic bath, it is likewise sensible to fit a sustaining plate under the faucets system to stop strain on the bathtub.
Fit the flexible tap connectors to the bottom of both taps utilizing 2 nuts as well as olives (occasionally provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet with the hole in the bath. Utilize the nut provided by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bath. Make sure you make use of every one of the supplied washing machines.
Connect the catch to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a comparable manner.The bath need to now prepare to be suited its last placement.
Removing Old Touches
If you need to change old faucets with new ones as a part of your installment, after that the first thing you ought to do is separate the water system. After doing so, turn on the faucets to drain pipes any water remaining in the system. The process of removing the existing faucets can be rather bothersome due to the restricted gain access to that is commonly the instance.
Utilize a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipelines to the taps. Have a cloth all set for the continuing to be water that will certainly come from the pipes. When the supply pipes have actually been gotten rid of, use the same device to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the single taps from transforming during this procedure. Once the taps have actually been removed, the holes in the bath/basin will certainly need to be cleansed of any kind of old securing compound.
Prior to moving on to fit the new taps, compare the pipeline links on the old taps to the new taps. If the old taps are longer than the new taps, after that a shank adapter is required for the new taps to fit.
Setting up the Bath tub
Utilizing the two wooden boards under its feet, put the bath tub in the required setting. The wooden boards are practical in evenly spreading the weight of the bath tub over the area of the boards as opposed to focusing all the weight onto four tiny points.
The next goal is to make sure that the bath tub is leveled all round. This can be accomplished by checking the spirit level and also changing the feet on the bath tub up until the spirit level checks out degree.
To mount taps, fit the bottom of the furthest flexible tap connector to the appropriate supply pipeline by making a compression join; after that do the same for the other tap.
Turn on the water supply as well as examine all joints as well as new pipework for leakages and tighten them if needed. Load the bathtub and also examine the overflow outlet and also the typical outlet for leaks.
Lastly, fix the bathroom paneling as explained in the manufacturer's instruction manual. Tiling and securing around the tub should wait till the tub has actually been utilized at least once as this will certainly settle it into its last placement.
Fitting New Touches
If the tails of the new taps are plastic, after that you will certainly need a plastic connector to avoid damages to the string. One end of the connector fits on the plastic tail of the faucet and also the other end provides a link to the existent supply pipelines.
If you require to fit a monobloc, after that you will certainly call for lowering couplers, which links the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next, place the tap in the placing hole in the bath/basin guaranteeing that the washers remain in place in between the faucet and also the sink. Safeguard the tap in place with the supplier supplied backnut. As soon as the tap is firmly in place, the supply pipelines can be connected to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with typical tap connectors. The previous type needs to be linked to the faucet finishes initially, tightening only by hand. The supply pipes can later on be connected to the various other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Bath tub
In the location where the bath meets the ceramic tile, it is necessary to secure the accompanies a silicone rubber caulking. This is very important as the fitting can move enough to crack a rigid seal, creating the water to permeate the wall surface in between the bathroom as well as the tiling, causing complications with dampness as well as feasible leaks to the ceiling listed below.
You can choose from a range of coloured sealants to blend in your fixtures and installations. They are sold in tubes and cartridges, and can securing voids approximately a size of 3mm (1/8 inch). If you have a larger void to fill, you can fill it with twists of drenched paper or soft rope. Bear in mind to constantly load the tub with water prior to securing, to permit the activity experienced when the bathtub remains in use. The sealant can crack relatively early if you do not think about this movement before securing.
Conversely, ceramic coving or quadrant floor tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are likewise quickly offered on the marketplace. It is suggested to fit the tiles making use of waterproof or waterproof glue as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a serious reader about A Step-by-Step Guide to Installing a Bathtub, I figured sharing that piece of content was a great idea. Sharing is caring. You won't know, you may just be helping someone out. I am grateful for your time. Please stop by our site back soon.
Reliable plumber? Dial now! Report this page